Grizzly Track Saw Review 2026: Worth It?

Track saws promise table saw accuracy without the table saw. Grizzly sells one for a price that makes Festool owners raise an eyebrow. The Grizzly PRO T33300ZX bundle costs around $289 and ships with three rails, two clamps, and a 48 tooth blade. That package would cost triple from a premium brand.

So the obvious question follows. Does a cheap track saw cut like an expensive one, or does the price tell you everything you need to know?

This review covers the unboxing, the cut quality, the plastic parts that feel cheap, the depth stop that annoys people, and the dust collection that only half works.

In a Nutshell:

• The price is the headline feature. The T33300ZX bundle sells for roughly $289 and includes three 36 inch rails, four connectors, two F clamps, an adjustable stop, and a stabilizer body. Buying that many rails from a premium brand costs far more.
• Cut quality lands between a circular saw and a table saw. Plywood edges come out clean enough for cabinet work after light sanding. Tear out on the keeper piece stays minimal. The off cut looks rougher.
• Build quality is the weak spot. The knobs feel square and cheap. The depth stop fights you during adjustment. Several owners report a slight rocking motion on the rail when they lean on one side.
• Dust collection works partially. The 1 1/2 inch port pulls most of the chips into a vacuum. A visible pile still lands on the off cut after every pass.
• The stock blade is better than expected but not the best. Many owners swap it for a fine tooth blade and report a noticeable jump in finish quality.
• Grizzly does not sell this saw on Amazon. You buy direct from Grizzly or through a few dealers, so compare it against Amazon options like WEN, Makita, and DEWALT before ordering.

What Is the Grizzly PRO T33300ZX Track Saw?

The Grizzly PRO T33300ZX is a corded plunge cut track saw sold as a complete kit. The saw itself carries the model number T33300. Grizzly also sells the saw alone for buyers who already own rails.

The motor rates at 1 1/2 HP, 120V, single phase, and pulls 9 amps. The blade measures 6 1/4 inches with 48 teeth and spins on a 3/4 inch arbor. Rim speed reaches 9,070 feet per minute.

Cutting depth reaches 2 5/32 inches without the rail and 1 31/32 inches with the rail underneath. Bevel range runs 0 to 45 degrees. The saw drops to 1 7/16 inches of depth once you tilt it to 45 degrees on the track.

A spring loaded riving knife sits behind the blade for kickback protection. The low profile guard lets you cut as close as 5/8 inch from a wall. Grizzly backs the unit with a one year warranty and keeps parts and phone support inside the United States.

Unboxing Experience: What Arrives in the Box

The box arrives heavier than you expect, around 27 pounds shipped. Three aluminum rails take up most of the weight and most of the length. The carton feels sturdy, though the inner packaging leans basic with cardboard dividers instead of molded foam.

The saw sits wrapped in plastic with the blade already installed. Pull it out and the green housing looks sharp. The plastic feels hollow when you tap it.

Next come the three 36 inch guide rails, each with a rubber splinter strip already attached. Four rail connectors, two F clamps, an adjustable stop, and a stabilizer body fill out the accessory bag. No systainer style case appears anywhere, so plan on storing the rails against a wall.

The printed manual stands out. Grizzly writes its own documentation in the United States, and the exploded parts diagram actually helps. Setup takes about fifteen minutes, mostly spent joining rails and checking the splinter strip alignment with a first test cut.

Build Quality and Feel in the Hand

This is where the price shows itself. The saw body feels light and a little hollow. The knobs and levers use hard plastic with square edges rather than the smooth molded shapes you find on premium saws.

The cam adjusters that set the fit between the base and the rail work well. Dial them in and the saw glides with almost no side play. That part earns real praise.

The rocking issue is the real concern. Press down hard on the left side of the saw and the right side can lift slightly off the rail. That motion changes the effective blade angle if your hand pressure shifts mid cut.

Plunging takes effort. The handle sits vertical and the thumb release sits angled toward the back. One handed plunging becomes tiring fast, and anyone with wrist pain will want two hands on the tool. The stabilizer body in the bundle helps, but it does not erase the issue.

Closest Amazon Pick: WEN Plunge Cut Circular Saw Bundle

Last update on 2026-10-27 / Affiliate links / Images from Amazon Product Advertising API

Grizzly does not list this track saw on Amazon, so the closest comparison shoppers actually see is the WEN plunge cut bundle with a 100 inch rail. It sits near the same price and targets the same buyer.

The WEN uses a 6.5 inch blade and a 10 amp motor. The rail package covers a full sheet of plywood in one pass, same as the Grizzly stack of three shorter rails. One long rail beats three joined rails for straightness, which matters more than most buyers realize.

WEN rails accept Festool and Makita style saws, so you keep an upgrade path. The Grizzly rail works with Festool clamps and the Grizzly saw rides on a Festool rail, but a Festool saw will not fit a Grizzly rail.

The WEN feels similar in the hand. Plastic parts, basic knobs, decent power. Owners consistently report straight, reliable cuts once they install a better blade. Dust collection performs about the same, which is to say acceptable and not impressive.

Top 3 Alternative for Grizzly PRO T33300ZX Track Saw

Last update on 2026-10-27 / Affiliate links / Images from Amazon Product Advertising API

Makita XPS01PTJ 18V X2 LXT Brushless Plunge Circular Saw Kit

Last update on 2026-10-27 / Affiliate links / Images from Amazon Product Advertising API

WEN CT1274 7.25 Inch Variable Speed Track Saw

Last update on 2026-10-27 / Affiliate links / Images from Amazon Product Advertising API

Festool Plunge Cut Track Saw TS 55 with 55 Inch Guide Rail

Motor Power and Cutting Performance

The 9 amp motor moves a 6 1/4 inch blade at 9,070 feet per minute. That combination handles sheet goods without complaint. Three quarter inch plywood, MDF, and melamine all cut at a steady walking pace.

Hardwood tells a different story. Push through 8/4 maple and you hear the motor load up. Slow your feed rate and the saw finishes the cut cleanly. Rush it and the blade burns the edge.

This saw has no soft start and no variable speed. It jumps to full RPM the instant you squeeze the trigger, which makes the first plunge feel abrupt. Premium saws smooth that out.

Depth capacity limits the saw to one pass on standard lumber thickness. At 1 31/32 inches on the rail, you can cut a two by material in a single pass at 90 degrees. Anything thicker requires a flip and a second cut, which introduces alignment risk.

Track System, Connectors, and Clamps

The aluminum extrusion feels solid and the anodized finish slides well after a coat of paste wax. Each 36 inch rail carries a rubber splinter strip that you trim with your first cut. That first pass sets a perfect zero reference line.

Joining rails works through four connectors and a set screw arrangement. Two rails give you 72 inches. Three rails give you 108 inches, enough for a full sheet ripped lengthwise.

Here is the catch. Every joint is a chance for a small bump or a slight angle change. Owners who take time to align the rails on a flat surface report clean joints. Owners who rush get a visible step in the cut.

The two F clamps slide into the bottom channel and tighten from below. They hold well and stay out of the saw path. The rails also grip with rubber strips underneath, so short cuts often need no clamps at all.

Cut Quality on Plywood, MDF, and Hardwood

Cut quality beats a circular saw by a wide margin. It does not match a well tuned table saw with a premium blade. That gap is smaller than the price gap, which is the whole argument for this tool.

On birch plywood the keeper side comes out nearly splinter free. Light sanding with 180 grit removes any fuzz. The off cut side shows more tear out because the splinter strip only protects one edge.

MDF cuts beautifully. The 48 tooth blade leaves a smooth face with no chipping. Melamine needs a scoring pass with a shallow depth setting first, then a full depth cut.

Hardwood results depend entirely on feed rate. Walnut and maple come out clean at a slow steady pace. The stock blade performs better than most included blades, though a quality 48 or 60 tooth replacement lifts the finish noticeably. Many owners call the blade swap the single best upgrade.

Dust Collection: Good, Not Great

The 1 1/2 inch dust port accepts a standard shop vacuum hose and also fits a Festool extractor hose without an adapter. Hook up a vacuum and most of the chips disappear.

Most is not all. A visible line of dust escapes around the blade housing during every cut. It tends to settle in a neat pile on top of the off cut rather than spraying across the shop.

Compare that to a bare circular saw and the Grizzly looks great. Compare it to a premium saw with a matched extractor and the Grizzly falls behind by a clear margin.

Cutting MDF makes the gap obvious. MDF dust is fine and it finds every leak. Wear a respirator regardless of which saw you own.

Run the vacuum on high, keep the hose short, and the shop stays reasonably clean. Without a vacuum attached, the saw fills the port and then dumps chips everywhere, so treat the vacuum as required equipment.

What the Grizzly Track Saw Does Not Do Well

Honest reviews list the failures. This saw has several.

The depth stop ranks first. It reads as though the saw sits directly on the workpiece, so you must add the rail thickness to every setting. Adjusting it feels gritty and the lock knob needs a firm grip.

The rocking motion on the rail ranks second. Uneven hand pressure can lift one side and shift your cutting angle. Careful technique solves it, but you should not have to compensate for your tool.

Plunge effort ranks third. The spring is stiff and the handle geometry works against your wrist. Long sessions leave your hand sore.

Long term durability draws mixed reports. Some owners run theirs for years with zero problems. Others report motor failures and describe the tool as poorly made. Grizzly handheld power tools carry a weaker reputation than Grizzly stationary machines, and this saw sits squarely in that pattern.

Finally, the rails are short. Three joints create three chances for error.

Pros and Cons of the Grizzly Track Saw

Pros

• Excellent value at roughly $289 for a saw plus three rails, four connectors, two clamps, an adjustable stop, and a stabilizer body
• Clean cuts on plywood and MDF that beat any freehand circular saw by a wide margin
• Spring loaded riving knife adds real kickback protection, a feature missing from several competing budget saws
• Cam adjusters remove side play between the base and the rail, giving a tight and repeatable glide
• Rails accept Festool clamps and the saw accepts a Festool extractor hose, so accessory options stay open
• United States based technical support, real parts availability, and a genuinely useful printed manual
• Works as a standard circular saw off the rail when you need quick rough cuts

Cons

• Plastic knobs and levers feel cheap and the housing sounds hollow
• Depth stop reads without rail thickness included and adjusts stiffly
• Slight rocking on the rail under uneven hand pressure can shift the cut angle
• Stiff plunge spring plus vertical handle makes one handed operation tiring
• Dust collection leaves a visible pile of chips on the off cut every pass
• Three joined rails create three potential alignment errors on long rips
• Mixed long term reliability reports, with some owners reporting motor failure
• Only a one year warranty compared to three years from several rivals

DEWALT DWS520K TrackSaw Kit: The Step Up Option

Last update on 2026-10-27 / Affiliate links / Images from Amazon Product Advertising API

Some buyers should skip the budget tier entirely. The DEWALT DWS520K sits in that next bracket and answers most of the Grizzly complaints.

The 12 amp motor includes soft start and variable speed control. That alone changes the feel of every plunge. The anti kickback mechanism locks the saw to the rail so it cannot climb backward.

DEWALT uses a dual edge track, which means you can cut from either side of the rail. The saw glides with essentially zero play and holds its bevel setting far better than budget alternatives.

Dust extraction performs a clear step above the Grizzly. Hook a vacuum to the port and very little escapes.

The trade off is money. The DWS520K costs roughly $500 with a 59 inch track, and additional rails cost real money. If you cut sheet goods weekly or earn income from the work, that extra spend pays for itself in saved time and fewer ruined panels.

Who Should Buy It and Who Should Skip It

Buy the Grizzly if you are a hobbyist who breaks down a few sheets of plywood each month. The accuracy upgrade over a circular saw and a clamped straightedge feels immediate. The price leaves money in your pocket for lumber.

Buy it if you have no room for a table saw. Apartment woodworkers and single car garage shops get real table saw results from a tool that hangs on a wall.

Buy it if you already own Grizzly machines and value having one support number for everything.

Skip it if you make your living with tools. Professionals should look at Makita, DEWALT, or Festool. Daily use exposes the plastic parts and the stiff plunge action quickly.

Skip it if you cut hardwood more often than sheet goods. The depth capacity and motor power favor plywood work.

Skip it if you want maximum rail length per dollar, because a single 100 inch rail beats three joined 36 inch sections every time.

Final Verdict: Worth Your Money in 2026?

The Grizzly PRO T33300ZX earns a qualified recommendation. It delivers roughly 80 percent of the cut quality of a premium track saw for roughly 30 percent of the price. That math works for a lot of people.

It also feels like a budget tool every time you touch it. The knobs, the depth stop, the plunge action, and the slight rail rocking all remind you what you paid.

Set your expectations correctly and you will be happy. This is a sheet goods breakdown tool for a home shop, not a production saw for a cabinet business.

Swap the blade, wax the rails, align the connectors carefully, and attach a vacuum. Do those four things and the saw performs well above its price class.

My honest score sits at 3.5 out of 5. The value rates a 5. The build quality rates a 3. If your budget can stretch to a Makita or DEWALT, stretch it. If it cannot, this saw beats freehand cutting every single day.

Frequently Asked Questions

Does Grizzly sell its track saw on Amazon?

No. Grizzly sells the T33300 and the T33300ZX bundle directly through its own website and through a handful of dealers such as Tractor Supply. Amazon listings for track saws under a Grizzly search return WEN, DEWALT, Makita, and Festool models instead. Buy direct if you want the Grizzly.

What is the maximum cutting depth of the Grizzly track saw?

The saw cuts 2 5/32 inches deep at 90 degrees without the rail underneath. With the rail in place the depth drops to 1 31/32 inches. At a 45 degree bevel the numbers fall to 1 5/8 inches without the rail and 1 7/16 inches with the rail.

Does the Grizzly saw work on Festool or Makita rails?

The Grizzly saw fits onto a Festool rail, though the blade sticks out well past the rubber splinter guard, which leaves your reference line inaccurate. A Festool saw will not fit a Grizzly rail because the groove is too narrow. Grizzly rails do accept Festool clamps and the saw accepts a Festool extractor hose.

Should I replace the included blade?

The included 48 tooth carbide blade performs better than blades bundled with most circular saws. Even so, many owners report a clear improvement in finish after installing a quality fine tooth blade. Remember the arbor measures 3/4 inch, so check that specification before ordering a replacement.

How long is the warranty?

Grizzly covers the track saw for one year against factory defects, including parts. Technical support and the parts warehouse operate inside the United States, which shortens wait times. Several competing brands offer three year warranties, so the coverage period counts as a weak point.

Can the Grizzly track saw cut a full sheet of plywood?

Yes. The bundle includes three 36 inch rails and four connectors, which combine into a 108 inch run. That length covers a 96 inch sheet with room to start and finish the cut. Align the joints carefully on a flat surface, because each connection can introduce a small step or angle change.

Is a track saw a real table saw replacement?

A track saw replaces a table saw for breaking down sheet goods and cutting long straight edges. It does not replace a table saw for narrow rips, repeat cuts against a fence, dadoes, or joinery. Many small shops run a track saw alongside a small bench saw and cover almost everything that way.